w201 Install Mercedes Benz PlugIn Keyless Entry Upgrade

28 Апр 2015 | Author: | No comments yet »
Mercedes-Benz W201

Install Instructions

Keyless with MB factory Alarm and outputs for the optional Parking Confirmation, Security LED

. You will the follwing tools:

Picture # 1 # 2 Picture # 3

FIRSTLY, disconnect the car or remove fuse # 12, which the central locking.

In the trunk lid of the you will see the key lock in the center, and to the of the lock, connected with a metal rod, you will see the Actuator’. If you use a flashlight, you will see a plastic wire connector into the lock actuator the top, and a yellow plastic line connected to the bottom. You to un-plug this round connector in the actuator, and re-plug the into the Aussie Keyless control box. Once the Keyless control box will in the cavity next to the lock in the trunk lid.

On some later model chassis, there is a small cover protecting the actuator and rod. Loosen by removing the 8 mm securing it. (Just let the piece of flop around, you don’t to remove it) Also remove the two 8 mm holding the lock actuator in so the actuator is loose and free to around, (Leave actuator in

Now the actuator is loose, you can remove the plastic wiring plug clear in color), from the lock actuator. It is jammed in and hard to get to. Also, there is a security clip on the side of the which holds the round plug in place. You need to this clip back trying to separate the round plug from the lock Pull on the plastic body of the Do not pull by the wires . as you may break (If you break the security clip, OK). Using long-nose will make this easier. Also, you can use a screwdriver as a to bend back the plastic clip, which holds the plug in place. (On newer there is no security clip and the is a black right angle plug, as illustrated.)

Once you have separated the electrical connector, plug in the entry control box to the cable was previously connected to the actuator.

. Make sure you line the two up correctly as you connect them. are two flat surfaces inside the you need to line up

Wrap electrical tape around the connector to prevent it from due to the vibration from the closing of the lid. Tie up any excess wires the yellow wire) in a loop and fix the pull-tie provided. The yellow is the antenna. Stretch it out straight the back wall of the trunk making sure it does not with the lock or actuator

Hide the Keyless entry box in the cavity next to the actuator in the lid. Wrap the control box in bubble wrap or foam to it some padding, and tie it in place a pull-tie to the vacuum line you see in the lid. (The Blue 15A will likely never but you can install it in such a way, it is visible and accessible.)

Re-install the two 8 mm securing the lock actuator to the lid, and re-install the plastic covering the lock actuator and rod.

Re-connect the car battery or fuse #12.

Mercedes-Benz W201

Close the doors, hood and on your car and hold the lock down on a remote for about 5 Push the Lock button on the remote a second time for 5 seconds, and the car should lock. You hear the electrical relays in the Keyless entry control box operated with the remote. If happens, press the UN-LOCK twice, and commence again.

At first, only one remote will work until the remote is programmed with the key code. Either remote can be the initiated, and either remote the programmed with the key code of the remote.

PROGRAMMING SECOND To program the second remote to you need to hold the LOCK on the working remote down for 15 Then hold the LOCK on the new remote down for 5 seconds. push the LOCK button on the new a second time. The Car should Both remotes should now the same electronic entry

USING YOUR KEYS: If you or UN-LOCK the car with your MB key, you may have to push the and then the LOCK buttons on the to cycle the system, as it sometimes confused if you use the mechanical key.

If you ever have a problem the system, simply disconnect the car and re-connect, or remove the Central fuse “#12” for 10 seconds and re-install. This will the system

A) Providing your alarm is installed and operational, Aussie Keyless entry III system activates the factory in the car in all models, except the 300TE/TD wagons. You can still activate the alarm, including on the station by locking your car with regular MB key. (The keyless Mark IV model control the factory alarm on a wagon).

B) The red button on the remote is NOT a panic It is for other remote programming not required on this MBZkeyless only conversion.

C) The Trunk-Pop on the remote is used as a finder to the parking lights if feature is

Mercedes-Benz W201


Mercedes-Benz W201
Mercedes-Benz W201

interesting records

Tagged as:

Here you can write a commentary on the recording "w201 Install Mercedes Benz PlugIn Keyless Entry Upgrade".

Sign in, to write a review.

Twitter-news
Our partners
Follow us
Contact us
Our contacts

dima911@gmail.com

Born in the USSR

423360519

About this site

For all questions about advertising, please contact listed on the site.


Mercedes-Benz catalog with specifications, pictures, ratings, reviews and discusssions about cars Mercedes-Benz.